Modification of Polylactide Nonwovens with Carbon Nanotubes and Ladder Poly(silsesquioxane)

Electrospun nonwovens of poly(L-lactide) (PLLA) modified with multiwall carbon nanotubes (MWCNT) and linear ladder-like poly(silsesquioxane) with methoxycarbonyl side groups (LPSQ-COOMe) were obtained. MWCNT and LPSQ-COOMe were added to the polymer solution before the electrospinning. In addition, nonwovens of PLLA grafted to modified MWCNT were electrospun. All modified nonwovens exhibited higher tensile strength than the neat PLA nonwoven. The addition of 10 wt.% of LPSQ-COOMe and 0.1 wt.% of MWCNT to PLLA increased the tensile strength of the nonwovens 2.4 times, improving also the elongation at the maximum stress.     

Carbide precipitates in solution-quenched PH13-8 Mo stainless steel: A small-angle neutron scattering investigation

This paper deals with the small-angle neutron scattering (SANS) investigation on solution-quenched PH13-8 Mo stainless steel. From the nature of the variation of the functionality of the profiles for varying specimen thickness and also from the transmission electron microscopy (TEM), it has been established that the small-angle scattering signal predominantly originates from the block-like metallic carbide precipitates in the specimen. The contribution due to double Bragg reflection is not significant in the present case. The single scattering profile has been extracted from the experimental profiles corresponding to different values of specimen thickness. In order to avoid complexity and non-uniqueness of the multi-parameter minimization for randomly oriented polydisperse block-like precipitate model, the data have been analyzed assuming randomly oriented polydisperse cylindrical particle model with a locked aspect ratio.     

微钢管内部强迫对流换热的实验研究

本文对以蒸馏水为工质,流过内径和外径分别为168μm、406μm和399μm、798μm的电加热不锈钢管时的换热进行了实验研究。通过对微钢管直接通电进行加热,并采用红外成像仪及专用放大镜头的非接触式方法,获得了各种恒定加热功率及不同雷诺数下的微钢管壁面的温度场分布,进而得到较为精确的壁面平均温度。由此计算了在层流态下的换热系数Nu数。实验结果表明,在层流下,内径为168μm及399μm的微钢管内部的Nu数分别比经典的Hansen准则式所得到的Nu数高出很多。     

Influence of oxidation time on semiconductive behaviour of thermally grown oxide films on AISI 304L

The oxide films formed on AISI 304L stainless steel at 300 °C in the oxidation time range between 2 and 4 h have been studied by photoelectrochemistry. Photocurrents were investigated as a function of the wavelength of the incident light and the electrode potential. The investigation allowed the determination of the semiconductive properties of the oxides. The oxide films showed n-type behaviour. A duplex structure of the oxide films has been suggested on the basis of the photocurrent spectra, with an internal oxide layer having an optical gap (E_g2 = 2.16-2.3 eV) depending on the applied potential and oxidation time, higher to that of the external oxide layer (E_g1 ≈ 1.9 eV). Significant variations in the amplitude of the photocurrent were detected as a function of the applied potential and the oxidation time.     

轻型汽车后桥半轴断裂件的组织及断口特征

采用光学显微镜和扫描电子显微镜等手段，对某轻型汽车40Cr后桥半轴断裂件的组织及断口特征进行了分析结果表明：半轴在调质处理时的淬火温度不够高，使其表层和心部组织中存在较多的铁素体相，造成了工件最终的硬度和疲劳强度不足，导致半轴在使用中发生扭转疲劳断裂．     

混凝土动态劈裂拉伸试验的数值模拟

采用LS-DYNA有限元编码程序，对混凝土的动态劈裂拉伸试验进行了数值模拟，给出了混凝土试样在不同类型加载情况下应力分布之间的差异，证实了动态劈裂拉伸试验的有效性，提出了改进试验方法的若干结论．     

Rugged distal tips for CO2 laser medicine

Low-loss and rugged distal tips for CO₂ laser have been proposed and fabricated based on a commercially available stainless steel (St) pipe. A method of smoothening the inner surface of the St pipe with a rough inner surface is put forward. Fabrication parameters, transmission properties, and mechanical strength of the cyclic olefin polymer-coated silver hollow St distal tip are experimentally discussed.     

Statistical Analysis of the Effect of Mineral Admixtures on the Strength of the Interfacial Transition Zone

Microscopic evidence indicates that the thickness of the interfacial transition zone (ITZ) between the aggregate and the cement paste is modified when mineral admixtures partially replace portland cement. Unfortunately, there is limited information on the significance of these microscopic modifications to the mechanical properties of the ITZ. This research reports experimental results on the shear and tensile strength of the ITZ as affected by the addition of the following mineral admixtures: silica fume, fly ash, and natural pozzolan. Statistical analysis was used to identify the significant parameters affecting the tensile and shear strength of the ITZ. Experimental results indicate that not only does the incorporation of silica fume and fly ash increase the strength of the ITZ, these mineral admixtures have a greater influence on the strength increase of the ITZ than in the strength increase of the cement paste.     

大型钢结构人行景观天桥的有限元分析

采用有限元方法对大型钢结构人行景观天桥进行了静力学、温度应力、动力学模态和初步的抗震能力分析,并就桥自重作用下的最大竖向位移和实际观测结果进行了比较,两者是一致的.计算结果表明:人行景观天桥在常规、温度极值改变和多遇地震荷载作用等多种工况下,现有的设计方案具有足够的强度、刚度和抗震能力.     

高强混凝土弯压极限应变试验研究与计算

由于混凝土材料理化特性的差异,高强混凝土的弯压极限应变明显地小于普通混凝土,依据试验结果分析了高强混凝土的弯压极限应变变化规律,并给出了它的计算公式.